| Mobile module | 4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps |
|---|
| SIM switch | 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection |
|---|
| Status | Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID |
|---|
| SMS | SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP |
|---|
| USSD | Supports sending and reading Unstructured Supplementary Service Data messages |
|---|
| Black/White list | Operator black/white list |
|---|
| Multiple PDN | Possibility to use different PDNs for multiple network access and services |
|---|
| Band management | Band lock, Used band status display |
|---|
| SIM idle protection service | When working with devices with two SIM slots, the one not currently in use will remain idle until the device switches to it, meaning that no data is used on the card until then. |
|---|
| APN | Auto APN |
|---|
| Bridge | Direct connection (bridge) between mobile ISP and device on LAN |
|---|
| Passthrough | Router assigns its mobile WAN IP address to another device on LAN |
|---|
| LAN | 1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX |
|---|
| Routing | Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing |
|---|
| Network protocols | TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL) |
|---|
| VoIP passthrough support | H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets |
|---|
| Connection monitoring | Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection |
|---|
| Firewall | Port forward, traffic rules, custom rules |
|---|
| Firewall status page | View all your Firewall statistics, rules, and rule counters. |
|---|
| Ports management | View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on. |
|---|
| Network topology | Visual representation of your network, showing which devices are connected to which other devices. |
|---|
| Hotspot | Captive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes and option to upload and download customised hotspot themes |
|---|
| DHCP | Static and dynamic IP allocation, DHCP Relay |
|---|
| QoS / Smart Queue Management (SQM) | Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e |
|---|
| DDNS | Supported >25 service providers, others can be configured manually |
|---|
| Network backup | Mobile, VRRP, Wired options, each of which can be used as an automatic Failover |
|---|
| Load balancing | Balance Internet traffic over multiple WAN connections |
|---|
| SSHFS | Possibility to mount remote file system via SSH protocol |
|---|
| Authentication | Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block |
|---|
| Firewall | Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T |
|---|
| Attack prevention | DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks) |
|---|
| VLAN | Port and tag-based VLAN separation |
|---|
| Mobile quota control | Mobile data limit, customizable period, start time, warning limit, phone number |
|---|
| WEB filter | Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only |
|---|
| Access control | Flexible access control of TCP, UDP, ICMP packets, MAC address filter |
|---|
| OpenVPN | Multiple clients and a server can run simultaneously, 27 encryption methods |
|---|
| OpenVPN Encryption | DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256 |
|---|
| IPsec | IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16) |
|---|
| GRE | GRE tunnel, GRE tunnel over IPsec support |
|---|
| PPTP, L2TP | Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support |
|---|
| Stunnel | Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code |
|---|
| DMVPN | Method of building scalable IPsec VPNs |
|---|
| SSTP | SSTP client instance support |
|---|
| ZeroTier | ZeroTier VPN client support |
|---|
| WireGuard | WireGuard VPN client and server support |
|---|
| Tinc | Tinc offers encryption, authentication and compression in it's tunnels. Client and server support. |
|---|
| ID range | Respond to one ID in range [1;255] or any |
|---|
| Allow Remote Access | Allow access through WAN |
|---|
| Custom registers | MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality |
|---|
| Supported functions | 01, 02, 03, 04, 05, 06, 15, 16 |
|---|
| Supported data formats | 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC) |
|---|
| Supported baud rates | From 300 to 115200 |
|---|
| Supported functions | 01, 02, 03, 04, 05, 06, 15, 16 |
|---|
| Supported data formats | 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII |
|---|
| Number of data bits | From 7 to 8 |
|---|
| Number of stop bits | 1 or 2 |
|---|
| Parity | None, Even, Odd |
|---|
| Flow | None, RTS/CTS, Xon/Xoff |
|---|
| Duplex | Full duplex |
|---|
| Supported baud rates | From 300 to 300000 |
|---|
| Supported functions | 01, 02, 03, 04, 05, 06, 15, 16 |
|---|
| Supported data formats | 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII |
|---|
| Number of data bits | 7 or 8 |
|---|
| Number of stop bits | 1 or 2 |
|---|
| Parity | None, Even, Odd |
|---|
| Flow | None, Xon/Xoff |
|---|
| Duplex | Half duplex |
|---|
| Protocol | HTTP(S), MQTT, Azure MQTT, Kinesis |
|---|
| Data to server | Extract parameters from multiple sources and different protocols, and send them all to a single server. |
|---|
| MQTT Gateway | Allows sending commands and receiving data from MODBUS Master through MQTT broker |
|---|
| Supported modes | TCP Master, DNP3 Outstation, RTU Master |
|---|
| DLMS Support | DLMS - standard protocol for utility meter data exchange |
|---|
| WEB UI | HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log |
|---|
| FOTA | Firmware update from server, automatic notification |
|---|
| SSH | SSH (v1, v2) |
|---|
| SMS | SMS status, SMS configuration, send/read SMS via HTTP POST/GET |
|---|
| Call | Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer |
|---|
| TR-069 | OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem |
|---|
| MQTT | MQTT Broker, MQTT publisher |
|---|
| SNMP | SNMP (v1, v2, v3), SNMP Trap |
|---|
| JSON-RPC | Management API over HTTP/HTTPS |
|---|
| MODBUS | MODBUS TCP status/control |
|---|
| RMS | Teltonika Remote Management System (RMS) |
|---|
| Cloud of Things | Allows monitoring of: Device data, Mobile data, Network info, Availability |
|---|
| ThingWorx | Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type |
|---|
| Cumulocity | Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength |
|---|
| Azure IoT Hub | Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type |
|---|
| CPU | Qualcomm QCA9531, MIPS 24kc, 650 MHz |
|---|
| RAM | 64 MB, DDR2 |
|---|
| FLASH storage | 16 MB, SPI Flash |
|---|
| WEB UI | Update FW from file, check FW on server, configuration profiles, configuration backup |
|---|
| FOTA | Update FW |
|---|
| RMS | Update FW/configuration for multiple devices at once |
|---|
| Keep settings | Update FW without losing current configuration |
|---|
| Operating system | RutOS (OpenWrt based Linux OS) |
|---|
| Supported languages | Busybox shell, Lua, C, C++ |
|---|
| Development tools | SDK package with build environment provided |
|---|
| GPL customization | You can now create your own custom firmware and web page application, with some examples to make the creation process easier; and brand our firmware by changing colours, logos, and so on to fit your or your clients’ needs. |
|---|
| GNSS | GPS, GLONASS, BeiDou, Galileo and QZSS |
|---|
| Coordinates | GNSS coordinates via WebUI, SMS, TAVL, RMS |
|---|
| NMEA | NMEA 0183 |
|---|
| NTRIP | NTRIP protocol (Networked Transport of RTCM via Internet Protocol) |
|---|
| Server software | Supported server software TAVL, RMS |
|---|
| Geofencing | Configurable multiple geofence zones |
|---|
| RS232 | Terminal block connector: TX, RX, RTS, CTS |
|---|
| RS485 | Terminal block connector: D+, D-, R+, R- (2 or 4 wire interface) |
|---|
| Serial functions | Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client |
|---|
| Input | 3 x Digital Input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high. 1 x Analog input (0 - 30 V) |
|---|
| Output | 3 x Digital Output, Open collector output, max output 30 V, 300 mA |
|---|
| Events | Email, RMS, SMS |
|---|
| I/O juggler | Allows to set certain I/O conditions to initiate event |
|---|
| Connector | 2 pins in 16-pin industrial terminal block |
|---|
| Input voltage range | 9 – 30 VDC, reverse polarity protection, surge protection +/-1 kV 50 µs max |
|---|
| Power consumption | Idle: < 1.2 W, Max: < 5 W |
|---|
| Ethernet | 1 x RJ45 port, 10/100 Mbps |
|---|
| I/O’s | 3 x Configurable I/O, 1 x Analog input in 16 pin terminal block |
|---|
| Status LEDs | 3 x connection status LEDs, 3 x connection strength LEDs, 1 x power LED, 1 x Eth port status LED |
|---|
| SIM | 2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, double stacked SIM tray |
|---|
| Power | 1 x 16-pin terminal block |
|---|
| Antennas | 1 x SMA connector for LTE, 1 x SMA connector for GNSS |
|---|
| RS232 | 4 pins in 16-pin terminal block (TX, RX, RTS, CTS) |
|---|
| RS485 | 4 pins in 16-pin terminal block (D+, D-, R+, R-) |
|---|
| Reset | Reboot/User default reset/Factory reset button |
|---|
| Casing material | Aluminum housing |
|---|
| Dimensions (W x H x D) | 83 x 25 x 74.2 mm |
|---|
| Weight | 165 g |
|---|
| Mounting options | DIN rail (can be mounted on two sides), flat surface placement |
|---|
| Operating temperature | -40 °C to 75 °C |
|---|
| Operating humidity | 10% to 90% non-condensing |
|---|
| Ingress Protection Rating | IP30 |
|---|
